Your shopping cart is empty.
Super Dilac Acidic low foaming Detergent cleans Metals surface. And useful product in maintenance and cleaning sector. In the food and Beverage industry, Metals Clean Britte is used as a rust remover. Largest seller and supplier of Super Dilac Acidic Detergent in INDIA Oman, GULF Middle East AND NAIROBI KENYA Africa.
RXSOL Super Dilac is a low foaming, high active, non-fuming nitric / phosphoric acid detergent descaler for use in a wide range of CIP applications in the Food and Beverage industry. Also used as Rust Stain cleaner Metal Clean Britte
A superior heavy duty and highly Concentrated liquid blend of surfactant & organic compound containing rust penetrating agent, solubilizer and inhibited phosphoric acid with ionic and non ionic emulsifier.
For polishing almost all metals, such as brass, copper, nickel, chrome, stainless steel, aluminium and even for machinery and golf clubs.
FOR TANK CLEANING
RECOMMENDATION : 0.2% TO 100%
FIELD:-
specially designed for removal of rust from any steel surface area and rust stain from Brass, Copper, S.S wood, ceramic and aluminium surfaces, painted or not. And act as surface brightner.
Procedure for Use :-
NOTE:-
For steel surfaces; remove oil, grease and old paint. Wet down entire surface with neat Super Dilac Acidic low foaming Detergent Metal Clean Bright- Rx and allow to dry. The second wash may be necessary. The surface should have a grey/white appearance when the Super Dilac Acidic low foaming Detergent Metal Clean Bright- Rx is dry. Steel surfaces will have a resistance to rust and will render a good base for paint.For removal of rust stains on painted surfaces and wood, Super Dilac Acidic low foaming Detergent Metal Clean Bright Rx should be applied at full concentration for heavy stains, or diluted to 20-50% for light stains. Allow to soak for 15 to 30 minutes and wash off with water. A second application may be necessary to remove the stubborn stains.
Spraying Direction:-
Using an empty/clean 210-litre drum, fill with 190 litres of fresh water and add 20 litres of Super Dilac Acidic low foaming Detergent Metal Clean Bright This makes a 10% solution, which can be sprayed onto areas in coated tanks where rust stains are showing and over actual rusted areas. Once spraying is completed, wait 20-30 minutes and fresh water rinses with lots of water if possible use Butterworth machines for a more efficient result. This method can be used in stainless tanks to “freshen up” the look of the stainless materials. Make sure to rinse the tank very well, as residual detergent within the Metal Clean Bright will show up in a Wall Wash.
Injection – Not suitable.
Re-circulation:–
When hand spraying is inadequate (too much area to cover), prepare a 2% - 5% solution in the tank using fresh water, heat solution to 50o C, then circulate the solution through Butterworth machines for 3 x 45 minutes drops minimum. When using fixed machine recirculate for a minimum of 3 cycles. Rinse out the tank using hot seawater 85o C for 2 hours making sure that there is no form remaining in the water at the pump stack drain cock. After the hot wash, the tank must be rinsed with fresh water and dried.
* If the mixture is allowed to overheat, it will soften epoxy/phenolic coating.
* Use a strainer at the pump stack when circulating any solution.
Tank Lining – Stainless / Epoxy, Phenolic
Specially designed for removal of rust from any steel surface area and rust stain from Brass, Copper, S.S wood, ceramic and aluminium surfaces, painted or not. And act as surface brightner.
When cleaning aluminium, brass & copper flush with water upon completion of cleaning immediately
Warning : In case of contact with skin, wash immediately with plenty of water. Use chemical resistance PVC gloves for skin contact and also use face mask for eye and face protection.
Read the Material Safety Data Sheet before using this products.