Product Code ::RXSOL-20-2006-020
Categories: Hold Solution-22
Product Short Description: Chembreak Emulsion Sludge Breaker Unique feature that dissociates slop to seperate oil and water.
Product Description:

RXSOL-20-2006-020 Slop Oil Emulsion Breaker has the unique feature that dissociates slop to seperate oil and water. This product is formulated to meet the ever changing regulations for the treatment of tank cleaning waste water after using petroleum based solvents, and Bunker "C" cleaners.

Product Application:

Ideally suited for slop tanks. Also recommended for local cleaning & degreasing of engine rooms, bilges & tank tops. Low toxicity, non - corrosive. Highly effective, economical solvent cleaner.

Product Dose:

For light contamination dilute with water in the ratio 1:20 . For medium contamination dilute with a petrosolvent. And for heavy contamination concentrated RXSOL-20-2006-020  is suggested.
 

For Engine Room & Cargo Tank Cleaner

Product Description:- RXSOL-20-2006-025 is an all purpose degreaser  emulsifiers, It is an excellent blend of powerful solvent base and emulsifying inorganic products .Specially designed  for engine room and cargo  tank cleaning .Main feature of RXSOL-20-2006-025 is, it finally dissociate slop emulsion  to separate oil and water .This provide us with ability to dispose of waste solution as per MARPOL & IMO rules and regulation .

Dosage:- Dose rate and results will vary depending on amount of contamination . For light contamination dilution with water up to 1:20 is recommended where as medium contamination dilution with Petro solvent , And for heavy contamination neat RXSOL CB 2006 is suggested to use.

Procedure of use :- RXSOL-20-2006-025 is  recommended for local cleaning & degreasing of engine rooms, bilges & tank  tops. It may be applied by brush, spray, immersion, soaking, or  any  other  conventional  means.RXSOL-20-2006-025 is used  neat. Allow a residence time of at least 20- 45 minutes where  possible, to ensure good penetration & emulsification. Finally wash the system with hot water & high pressure.The emulsion residue after cleaning must be allowed  to separate  in a holding tank for atleast 3-5 hours before passing through an oily water separator.

Tank Cleaning after Mineral Oils/ Lube Oils / Slope-Black Oil
1 ) Fill the tank with 1-35 litres per ton wash water.Best results are obtained when water is heated to a   temperature  between  65°C & 80°C  then  stripped  constantly and transferred  to a holding  tank  for  separation.The time for this will vary depending on amount of RXSOL-20-2006-025  used & nature of oil being cleaned.Generally,12 hours should be sufficient before the water phase can be removed.
2) Direct Cleaning.Spray directly RXSOL-20-2006-025 on tank surfaces to be cleaned, left  for at least 30  minutes.Finally wash with hydrogating (high pressure) machine. Hot water between 50°C & 80°C recommended.

Product Note:
Hashtag: #MarineChemical #TankCleaner #OilFieldChemical #ChemicalManufacturer #ChemicalSupplier #WaterTreatmentChemical #ROchemicals #ReverseOsmosisChemical #Dispersant #Demulsifier #WaterlessHandCleaner #AirC
Free Delivery / Supply Locations : 
Oman, Bahrain, Abu Dhabi, Ajman, Al Ain, Dubai, Ras Al-Khaimah, Ras al Khaimah, Fujairah, Sharjah, Umm Al Quwain, Fujairah, Ruwais, Mina (Port) Zayed, Khalifa Port, Kizad, Port Rashid, Jebel Ali Port, DP WORLD, Jebel Ali Free Zone, Khor Fakkan Container Terminal, Port Rashid, Jebel Ali Port, Mina Kalid Port, Khor Fhakan Port ( Khawr Fakkan, Khawr al-Fakkan ), Sharjah Creek, Ajman, Port of Hamriyah, Mina Zayed Port, Mussafah port, Khalifa Port, Umm al-Nar Port, Um Al Quwain Port, Saqr Port, Port of Fujairah, Dibba Port, Jebel Dhanna, Mina Al Hamriya, Mina Rashid, All United Arab Emirates